Why Is My Roman Blind Pulling Up Unevenly or Crooked?
A Roman blind that starts lifting unevenly, with one side or one section higher than another, is a common and frustrating problem.
The good news is that it doesn't necessarily mean you need a new Roman blind, or even a new headrail. Modern Roman blind cassette systems are made up of several individual components, and uneven lifting can often be traced to a lifting cord, cord adjuster, ring or cord drum that simply needs checking or resetting.
In this guide, we'll work through the most likely causes, starting with the easiest things to check.

How Should a Roman Blind Lift?
Inside a modern Roman blind headrail, the operating chain turns a control mechanism. This rotates the square drive rod running through the headrail.
Several cord drums or spools are fitted onto this rod. As the rod rotates, the drums turn together, winding in the lifting cords and raising the blind.
When everything is correctly positioned and adjusted, the lifting points should work together and the blind should rise evenly.
If one lifting point is effectively shorter, longer or operating differently from the others, the blind can start to lift crooked.
1. Check the Safety Toggles / Cord Adjusters
Start at the back of the fabric blind.
Look at the bottom of each lifting cord and check the position of the safety toggles or cord adjusters.
They should be set so the lifting points are level with one another.
If one cord has been adjusted shorter than the others, that section of the blind will start lifting first. If one is longer, that section may lag behind.
This is one of the simplest things to check and may save you from unnecessarily dismantling the headrail.
2. Check the Lifting Cords
Follow each lifting cord up the back of the blind.
Look for:
Fraying or wear
A partially broken cord
Knots or tangles
A cord caught behind the fabric
A cord that has become unusually short
Anything preventing the cord from moving freely
All the lifting cords need to move freely as the blind raises and lowers.
What if a lifting cord is damaged?
A damaged lifting cord doesn't normally mean that the complete cord drum or headrail needs replacing.
If a cord is frayed, broken or has become too short, it can be replaced using 1.2mm blind cord.
We'll cover the complete procedure for replacing a Roman blind lifting cord in a separate repair guide.
3. Check the Roman Blind Rings or Tape Loops
Next, inspect the blind rings or tape loops running vertically up the back of the fabric.
The lifting cord should pass cleanly through each one.
Check that none of the rings has:
Become detached from the blind
Broken
Pulled out of position
Become caught or twisted
A missing or damaged ring can change the route of the lifting cord and affect how that section of the blind rises.
Replacement Roman blind rings can normally be fitted without replacing the blind or headrail.
4. Check That Each Cord Runs Straight to Its Cord Drum
Now look at where each lifting cord enters the headrail.
Ideally, the cord should run reasonably straight upwards from its row of rings to the corresponding cord drum or spool.
Cord drums can be positioned along the square drive rod to correspond with the lifting points on the fabric blind.
If a drum has shifted sideways, the lifting cord may start pulling at an angle rather than vertically.
Check the position of each drum against the lifting-cord line beneath it and reposition where necessary.
5. Compare the Cord on Each Drum
This is an important check that's easily overlooked.
When a Roman blind has been set up correctly, the cord drums should all begin from the same starting position.
With the blind fully lowered, look at the lifting cord on each drum.
You should normally see a similar line of cord running across each drum, with approximately the same starting amount of cord wound onto them.
If one drum has noticeably more or less cord wrapped around it than the others, that lifting point may be starting from a different position.
As the blind rises, one section can then begin lifting before or after the others.
Does the Blind Start Crooked or Become Crooked as It Rises?
This can provide a useful clue.
If the blind is already uneven as it begins to lift, check the cord adjusters and fabric-side lifting arrangement first.
If the blind starts reasonably level but becomes progressively more uneven as it rises, pay particular attention to the lifting cords, cord path, drum positions and the amount of cord wound onto each drum.

How to Reset Uneven Roman Blind Cord Drums
If you've checked the lifting system and find that the cord drums are starting with different amounts of cord wound around them, the drums can be reset.
Before starting, lower the blind and remove the headrail from its mounting brackets so that you can work on it safely.
1. Release the mechanism end
Remove the end-cap/cover retaining screws.
This releases the cover and control mechanism so the internal assembly can be withdrawn from the aluminium headrail.
2. Slide the internal assembly out
Carefully slide the control mechanism, square drive/tilt rod and cord drums out together from the mechanism end of the headrail.
On this type of system, the square drive rod is secured to the control mechanism with a hex-key fixing. The assembly therefore needs to be withdrawn from the mechanism end rather than pulled through from the opposite end.
3. Slide the cord drums off the square rod
Once the assembly is accessible, slide each cord drum individually off the square drive rod.
This is necessary because the drum cannot independently return to its starting position while it remains engaged with the square rod.
4. Fully extend each lifting cord
With each drum free from the drive rod, carefully pull its lifting cord out to its maximum length.
Repeat this with each drum.
This returns all the drums to the same starting position.
5. Refit the cord drums
Slide the drums back onto the square drive rod.
Position each drum approximately above the corresponding lifting-cord position on the fabric blind.
The positioning doesn't normally need to be perfect to the millimetre, as small adjustments can be made when the blind is refitted.
6. Reassemble the headrail
Slide the complete mechanism, drive rod and drum assembly back into the aluminium headrail.
Make sure the lifting cords exit cleanly in their correct positions and aren't trapped or tangled.
Refit the mechanism cover/end components and replace the retaining screws.
7. Remount and test the Roman blind
Refit the headrail onto its mounting brackets and check that each lifting cord runs vertically through its rings or tape loops.
Check the safety toggles/cord adjusters again and make any small adjustments necessary to level the blind.
Operate the blind slowly and watch the lifting points.
They should now begin lifting together and remain substantially level as the blind rises.
Don't Immediately Replace the Control Mechanism
If the operating chain turns normally, the square drive rod rotates and all the cord drums are turning, the control mechanism is performing its basic job.
A crooked Roman blind doesn't automatically mean the mechanism has failed.
It's worth checking the lifting cords, adjusters, rings and cord drums before buying a replacement mechanism.
This is one of the advantages of a modern Roman blind cassette: many problems can be diagnosed and repaired at component level.
What if the Blind Is Still Lifting Unevenly?
If resetting the drums doesn't solve the problem, work through the system again methodically.
Check that:
All cord adjusters are set evenly
No lifting cord is damaged, stretched, tangled or obstructed
All rings or tape loops are intact
Each lifting cord follows a straight path
Each cord drum is positioned over its corresponding lifting point
The cords are winding cleanly and evenly onto the drums
All the drums rotate when the blind is operated
If one component is damaged, it can often be replaced individually.
Need to Identify Your Roman Blind Parts?
Roman blind headrails are available in different profiles, and components from different systems are not necessarily interchangeable.
Before ordering a replacement mechanism, cord drum, bracket or other headrail component, identify which system you have.
Our Roman Blind Parts Explained guide shows the main components and how they interact, while our Roman Blind Headrail Identification Guide can help you distinguish between common Deluxe, Professional and Elite-type profiles.
At Blind Parts Hub, we stock a growing range of Roman blind replacement parts, including mechanisms, cord drums/spools, lifting components and made-to-measure Roman blind headrails.
If you're unsure what you need, send us a clear photograph of the headrail and the part you're having trouble with and we'll help you identify the most suitable option.




Comments